V-Tec AT16/C5 Dokumentacja Strona 58
- Strona / 94
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Si2400
58 Rev. 1.3
Reset settings = 0011_0000
b
(0x30)
S36 (ARM1). Alarm 1 (!7 Mode Only)
BitD7D6D5D4D3D2D1D0
Name
POF PON IDKT IT
Type R/W R/W R/W R/W
Bit Name Function
7:6 POF Pulse Off Time.
00 = 25 ms.
01 = 50 ms.
10 = 65 ms.
11 = Use S2C register.
5:4 PON
Pulse On Time.
00 = 25 ms.
01 = 50 ms.
10 = 65 ms.
11 = Use S2B register.
3:2 IDKT Intermessage Delay and Kissoff Timeout.
This register field defines two parameters. The Intermessage Delay defines the time the Si2400
waits prior to sending a subsequent message. The Kissoff Timeout defines the time the Si2400
waits for a Kissoff Tone prior to declaring that there is no kissoff tone detected.
00 = Intermessage Delay is measured relative to the end of Kissoff and it is a fixed delay
of 2.4 s. The Kissoff Timeout is measured relative to the end of Kissoff and it is a fixed
value of 2 s.
01 = Intermessage Delay is measured relative to the end of Kissoff and it is determined by
S1F[4:0] (IMT). The Kissoff Timeout is measured relative to the end of Kissoff and it is deter-
mined by S1F[7:5] (KOT).
10 = Intermessage Delay is measured relative to the end of the previous message and it is a
fixed delay of 3.4 s. The Kissoff Timeout is measured relative to the end of Kissoff and it is a
fixed value of 2 s.
11 = Intermessage Delay is measured relative to the end of the previous message and it is
determined by S1F[7:5] (KOT). The Kissoff Timeout is measured relative to the end of Kissoff
and it is determined by S1F[7:5] (KOT).
1:0 IT
Interdigit Timing.
The controlled timing between the pulse digits.
00 = The timing between the end of a digit to the start of the next digit is fixed at 660 ms.
01 = The timing between the end of a digit to the start of the next digit is defined by the S2D
register.
10 = The timing between the start of a digit to the start of the next digit is fixed at 800 ms.
11 = The timing between the start of a digit to the start of the next digit is defined by the S2D
register.
Note: S36 is reconfigured as Alarm 1, a bit-mapped register, in !7 mode only. In all other modes, S36 is SKDTL (Second
Kissoff Tone Detect Length).
- Features 1
- Applications 1
- Description 1
- Functional Block Diagram 1
- 2 Rev. 1.3 2
- TABLE OF CONTENTS 3
- 1. Electrical Specifications 4
- Table 2. Loop Characteristics 5
- Table 3. DC Characteristics 6
- Table 4. DC Characteristics 6
- Table 5. AC Characteristics 7
- for K-Grade, T 8
- –40 to 85°C for B-Grade) 8
- = –40 to 85°C for B-Grade) 9
- 10 Rev. 1.3 10
- 3. Bill of Materials 11
- 12 Rev. 1.3 12
- 4. Analog Input/Output 13
- 5. Functional Description 14
- 5.1. Digital Interface 15
- 16 Rev. 1.3 16
- 5.3. Low Power Modes 17
- 5.4. Global DAA Operation 17
- 18 Rev. 1.3 18
- Rev. 1.3 19 19
- 20 Rev. 1.3 20
- 5.6. Loop Current Detection 21
- 5.7. Carrier Detect/Loss 21
- 5.8. Overcurrent Detection 21
- 5.11. PCM Data Mode 23
- Figure 10. Signal Routing 24
- 5.12. Analog Codec 25
- 5.14. V.42 HDLC Mode 26
- 5.15. Fast Connect 27
- Table 16. MCKR Configurations 28
- 6.1. Command Line Execution 29
- 30 Rev. 1.3 30
- 6.4. S-Register Control 31
- 32 Rev. 1.3 32
- 6.5.4. A1 34
- 6.5.5. !2 34
- 6.5.6. !7 34
- Table 19. !7 Parameters 35
- Figure 12. !7 Security Timing 36
- Progress 37
- S19 S1A S1B S16 S17 S18 38
- Table 23. DTMF 39
- 7.1. DSP Registers 40
- SE8 SE6 SE5 41
- DSP Reg. Addr 41
- 7.2. Call Progress Filters 42
- 8. S Registers 43
- 44 Rev. 1.3 44
- Rev. 1.3 45 45
- 46 Rev. 1.3 46
- Rev. 1.3 47 47
- 50 Rev. 1.3 50
- Rev. 1.3 51 51
- 52 Rev. 1.3 52
- Rev. 1.3 53 53
- 54 Rev. 1.3 54
- Rev. 1.3 55 55
- 56 Rev. 1.3 56
- 58 Rev. 1.3 58
- Kissoff Tone Detect Length) 58
- Rev. 1.3 59 59
- 60 Rev. 1.3 60
- Rev. 1.3 61 61
- 62 Rev. 1.3 62
- Rev. 1.3 63 63
- Rev. 1.3 65 65
- 66 Rev. 1.3 66
- Rev. 1.3 69 69
- 70 Rev. 1.3 70
- Rev. 1.3 71 71
- 72 Rev. 1.3 72
- Rev. 1.3 73 73
- 74 Rev. 1.3 74
- Rev. 1.3 75 75
- 76 Rev. 1.3 76
- Rev. 1.3 77 77
- DAA Isolation Barrier 78
- Emissions/Immunity 78
- DC Termination 79
- AC Termination 80
- Ringer Impedance 80
- DTMF Dialing 80
- Pulse Dialing 80
- Billing Tone Detection 80
- Symbol Value 81
- In-Circuit Testing 82
- Compliance Test Commands 83
- Introduction 84
- APPENDIX C—UL1950 3RD EDITION 85
- 9. Pin Descriptions: Si2400 86
- Rev. 1.3 87 87
- 10. Pin Descriptions: Si3015 88
- Receive Input 89
- Filter 2 89
- Pin # Pin Name Description 89
- 11. Ordering Guide 90
- Millimeters 91
- Revision 1.1 to Revision 1.2 92
- Revision 1.2 to Revision 1.3 92
- Rev. 1.3 93 93
- CONTACT INFORMATION 94
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa V-Tec AT16/C5
(19 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji